PreviousPro2 Power Supply 230Vac/24...

NextPro2 Power Supply 230Vac/24...

Pro2 Power Supply 230Vac/24Vdc 40A (960W)

WAGO Power supply; Pro 2; 1-phase; 24 VDC output voltage; 40 A output current; TopBoost + PowerBoost

Free shipping on Web orders over $100

$1030.00

(Each excl GST)

Global Stock

Quantity Breaks

25+

$1,030.00

SKU: WAGO-2787-2448 Manufacturer part number: 2787-2448 Manufacturer: WAGO

Qty:

Overview
Specifications
Contact Us

Technical data

Nominal output voltage Uo nom	DC 24 V (SELV)
Output voltage range	DC 24 … 28 V (adjustable)
Default setting	DC 24 V
Nominal output current Io nom	40 A (24 VDC)
Nominal output power	960 W
Control deviation	≤ 1 %
Residual ripple	≤ 70 mV (peak-to-peak)
Current limitation	1.1 x Io nom (typ.)
Overload behavior	TopBoost/PowerBoost/Time-limited constant current mode (other overload behaviors can be set)
PowerBoost	DC 60 A (5 s)
TopBoost	up to 600 %
Power loss Pl	≤ 1.5 W (Standby); ≤ 2.4 W (No load); ≤ 40 W (230 VAC; Nominal load)
Efficiency (typ.)	96 % (230 VAC; 40 A; 25 °C); 96.3 % (230 VAC; 30 A; 25 °C)
Signaling	Optical status indication (DC OK; load; warning and error states)
	Digital signal input and output (DI/DO)
Communication	Communication interface, can be used with WAGO USB Communication Cable (750-923) or IO-Link Communication Module (2789-9080) or Modbus RTU Communication Module (2789-9015)
Internal fuse	T 10 A / 250 VAC
Required backup fusing	An external DC fuse is required for the DC input voltage.
Recommended backup fusing	16 A (for USA/Canada: 15 A)
Isolation voltage (pri.-sec., AC)	3,510 V
Isolation voltage (pri.-GND, AC)	2,200 V
Isolation voltage (Sec.-GND)	DC 0.5 kV
Isolation voltage (Sec.-Signal)	DC 0.5 kV
Protection class	I
Protection type	IP20 (per EN 60529)
Resistance to reverse feed	≤ DC 35 V
Overvoltage category	III (≤ 2000 m a. s.l.); II (> 2000 m a. s.l.)
Pollution degree	2
Transient suppression (primary)	Yes
Overvoltage protection; secondary	Internal protective circuit
	≤ 35 VDC (in the event of a fault)
Short-circuit-protected	Yes
Open-circuit-proof	Yes
Parallel operation	Yes
Series operation	Yes
MTBF	> 900,000 h (per IEC 61709)
Phases	1
Nominal input voltage Ui nom	1 x AC 200 … 240 V
Input voltage range	AC 180 … 264 V; DC 130 … 240 V
Nominal mains frequency range	47 … 63 Hz; 0 Hz
Input current Ii	≤ 4.3 A (240 VAC; Nominal load); ≤ 5.1 A (200 VAC; Nominal load)
Inrush current	≤ 10 A (after 1 ms)
Power factor	≥ 0.98 (240 VAC)
Power factor correction (PFC)	Active
Mains failure hold-up time	≥ 25 ms (230 VAC)

Connection data

Connection type (1)	Input/Signaling
Connection technology	CAGE CLAMP®
WAGO Connector	WAGO 721 Series
Solid conductor	0.08 … 2.5 mm² / 28 … 12 AWG
Fine-stranded conductor	0.08 … 2.5 mm² / 28 … 12 AWG
Fine-stranded conductor; with insulated ferrule	0.25 … 1.5 mm² / 20 … 16 AWG
Fine-stranded conductor; with uninsulated ferrule	0.25 … 2.5 mm² / 20 … 14 AWG
Strip length	8 … 9 mm / 0.31 … 0.35 inch
Connection type 2	Output
Connection technology 2	Push-in CAGE CLAMP®
WAGO Connector 2	WAGO 831 Series
Solid conductor 2	0.5 … 10 mm² / 20 … 8 AWG
Fine-stranded conductor 2	0.5 … 10 mm² / 20 … 8 AWG
Fine-stranded conductor; with insulated ferrule 2	0.5 … 6 mm²
Fine-stranded conductor; with uninsulated ferrule 2	0.5 … 6 mm²
Strip length 2	13 … 15 mm / 0.51 … 0.59 inch

Physical data

Width	120 mm / 4.724 inch
Height	130 mm / 5.118 inch
Depth from upper edge of DIN-rail	130 mm / 5.118 inch
Note (dimensions)	Height without connector
	Height with connector: 169 mm

Mechanical data

Mounting type

DIN-35 rail

SKU WAGO-2787-2448

GTIN 4055143878296

We strive to provide you with the best information we can, considering the images are not to scale and do not represent detailed perspectives of the respected products. If you notice any errors or omissions in this information, please let us know using the contact us tab on this page.

Products specifications

Attribute name	Attribute value
Locally Stocked in Australia	Only Show Stocked Items

Your name *

Your email *

Enquiry *