| General specifications |
|---|
| Sensing range |
90 ... 2000 mm |
| Adjustment range |
120 ... 2000 mm |
| Dead band |
0 ... 90 mm |
| Standard target plate |
100 mm x 100 mm |
| Transducer frequency |
approx. 200 kHz |
| Response delay |
minimum : 65 ms
factory setting: 125 ms |
| Memory |
|---|
| Non-volatile memory |
EEPROM |
| Write cycles |
100000 |
| Indicators/operating means |
|---|
| LED green |
solid: Power on
flashing: Standby mode or IO link communication |
| LED yellow 1 |
solid: Object in evaluation range
flashing: Learning function, object detected |
| LED yellow 2 |
solid: Object in evaluation range
flashing: Learning function, object detected |
| LED red |
solid red: Error
red, flashing: program function, object not detected |
| Electrical specifications |
|---|
| Operating voltage |
10 ... 30 V DC , ripple 10 %SS
15 ... 30 V voltage output |
| No-load supply current |
≤ 60 mA |
| Power consumption |
≤ 1 W |
| Time delay before availability |
≤ 120 ms |
| Interface |
|---|
| Interface type |
IO-Link |
| Protocol |
IO-Link V1.0 |
| Transfer rate |
Acyclical: typical 95 Bit/s |
| Cycle time |
min. 33.6 ms |
| Mode |
COM2 (38.4 kBit/s) |
| Process data width |
16 bit |
| SIO mode support |
yes |
| Input/Output |
|---|
| Input/output type |
1 synchronization connection, bidirectional |
| |
0 Level |
0 ... 1 V |
| |
1 Level |
4 V ... UB |
| |
Input impedance |
> 12 kΩ |
| |
Output rated operating current |
< 12 mA |
| |
Pulse length |
0.5 ... 300 ms (level 1) |
| |
Pulse interval |
≥ 33 ms (level 0) |
| Synchronization frequency |
|
| |
Common mode operation |
≤ 30 Hz |
| |
Multiplex operation |
≤ 33 Hz / n , n = number of sensors , n ≤ 10
(factory setting: n = 5 ) |
| Output |
|---|
| Output type |
1 push-pull (4 in 1) output, short-circuit protected, reverse polarity protected
Current output 4 mA ... 20 mA or
voltage output 0 V ... 10 V configurable |
| Rated operating current |
200 mA , short-circuit/overload protected |
| Voltage drop |
≤ 2.5 V |
| Resolution |
current output: evaluation range [mm]/3200 but ≥ 0.35 mm
voltage output: evaluation range [mm]/4000 but ≥ 0.35 mm |
| Deviation of the characteristic curve |
≤ 0.2 % of full-scale value |
| Repeat accuracy |
≤ 0.1 % of full-scale value |
| Switching frequency |
≤ 4 Hz |
| Range hysteresis |
1 % of the adjusted operating range (default settings), programmable |
| Load impedance |
current output: ≤ 300 Ohm
voltage output: ≥ 1000 Ohm |
| Temperature influence |
≤ 1.5 % from full-scale value (with temperature compensation)
≤ 0.2 %/K (without temperature compensation) |
| Compliance with standards and directives |
|---|
| Standard conformity |
|
| |
Standards |
EN IEC 60947-5-2:2020
IEC 60947-5-2:2019
EN 60947-5-7:2003
IEC 60947-5-7:2003 |
| Approvals and certificates |
|---|
| UL approval |
cULus Listed, Class 2 Power Source |
| CCC approval |
CCC approval / marking not required for products rated ≤36 V |
| Ambient conditions |
|---|
| Ambient temperature |
-25 ... 70 °C (-13 ... 158 °F) |
| Storage temperature |
-40 ... 85 °C (-40 ... 185 °F) |
| Mechanical specifications |
|---|
| Connection type |
Connector plug M12 x 1 , 5-pin |
| Housing diameter |
30 mm |
| Degree of protection |
IP67 |
| Material |
|
| |
Housing |
Stainless steel 1.4305 / AISI 303
TPU
Polyamides |
| |
Transducer |
epoxy resin/hollow glass sphere mixture; polyurethane foam |
| Mass |
72 g |
| Factory settings |
|---|
| Output 1 |
near switch point: 120 mm
far switch point: 2000 mm
Output mode: Window mode
output behavior: NO contact |
| Output 2 |
near limit: 120 mm
far limit: 1000 mm
Output mode: rising ramp
output behavior: Current output 4 mA ... 20 mA |
| Beam width |
wide |
